Use a LED light bar to the tailgate of the truck to include stylish extra backup lights for your vehicle. LEDs are better than traditional auto lights and require less energy to operate. Frequently, truck LED light bars include trailer hitch accessories, meaning they just plug in to the wiring connector that's accustomed to connect your vehicle's lights to some trailer's lights. Mount the LED light bar on your truck and plug the wires directly into install your personal backup safety lights.
1
Clean from the mounting surface where you will install the LED light bar in your truck with rubbing alcohol along with a flannel.
2
Find the middle of the tailgate around the truck and the middle of the LED light bar. Align the middle of the SMD 5050 RGB waterproof LED Bar using the tailgate center. Remove the protective plastic strip in the adhesive on the rear of the LED light bar and press the sunshine bar to the tailgate with firm, even pressure to add it towards the truck.
3
Locate the flat trailer connector beneath the truck, close to the trailer hitch. It will likely be attached to four wires. Place the plastic finish from the LED wire connector in to the flat trailer connector. Use plastic zip ties to secure the LED wires onto the foot of the18 wheeler, close to the flat trailer connector.||Waterproof LED Bar 60LEDS
2011年12月4日星期日
2011年11月23日星期三
Steps to make an LED Projector
A LED projector is much like any projector for the reason that it takes a lens to concentrate the look although, unlike those of an incandescent bulb, the LED source of light uses less energy and does not generate warmth. You may make your personal LED slide-like projector from the couple of supplies acquired from the hobby store or electronics store, coupled with an LED torch. A couple of supplies that many homes may have available is going to be needed too.|Waterproof LED Bar 60LEDS
1
Take away the cover in the shoe box. Put the shoe box flat facedown on the work surface. Measure across the size of the shoe box having a tape-measure. Cut with the shoe box in the midway point having a utility knife.
2
Stand each 1 / 2 of the shoe box to ensure that the cut finish is facing lower. Put the reflector from the LED torch against the top among the shoe box halves. Draw a circle round the reflector around the shoe box having a pencil. Take away the LED torch. Eliminate the circle using the utility knife. Take away the cutout circle in the shoe box half.
3
Contain the slide to ensure that the dull side is facing you. Tape the slide towards the reflector from the LED torch with strips of duct tape. Put the reflector from the LED torch from the cutout circle. Tape the reflector towards the shoe box with strips of duct tape.
4
Put the 1 / 2 of the shoe box which has the LED torch facedown on the ground a feet from a wall using the LED torch facing you.
5
Put the fresnel lens against the top other shoe box halves. Draw a plan round the lens around the shoe box having a pencil. Take away the lens. Eliminate the rectangle using the utility knife. Take away the cutout rectangle in the shoe box half. Put the lens from the cutout rectangle. Tape the lens towards the shoe box with strips of duct tape.
6
Put the 1 / 2 of the shoe box facedown on the ground using the fresnel lens facing the wall. Fall into line the 2 shoe box halves to ensure that they're despite one another.|SMD 5050 RGB LED Bar 30LEDS
7
Turn the LED torch on. Switch off the area light. Move the shoe box half which has the fresnel lens toward another shoe box half to concentrate the look from the slide that's now being forecasted around the wall.
Tips & Alerts
The thin style of a fresnel lens causes it to be perfect for taking more oblique light compared to a bulky glass lens.A LED projector is much like any projector for the reason that it takes a lens to concentrate the look although, unlike those of an incandescent bulb, the LED source of light uses less energy and does not generate warmth. You may make your personal LED slide-like projector from the couple of supplies acquired from the hobby store or electronics store, coupled with an LED torch. A couple of supplies that many homes may have available is going to be needed too.
1
Take away the cover in the shoe box. Put the shoe box flat facedown on the work surface. Measure across the size of the shoe box having a tape-measure. Cut with the shoe box in the midway point having a utility knife.
2
Stand each 1 / 2 of the shoe box to ensure that the cut finish is facing lower. Put the reflector from the LED torch against the top among the shoe box halves. Draw a circle round the reflector around the shoe box having a pencil. Take away the LED torch. Eliminate the circle using the utility knife. Take away the cutout circle in the shoe box half.
3
Contain the slide to ensure that the dull side is facing you. Tape the slide towards the reflector from the LED torch with strips of duct tape. Put the reflector from the LED torch from the cutout circle. Tape the reflector towards the shoe box with strips of duct tape.
4
Put the 1 / 2 of the shoe box which has the LED torch facedown on the ground a feet from a wall using the LED torch facing you.|LED Strip Light
5
Put the fresnel lens against the top other shoe box halves. Draw a plan round the lens around the shoe box having a pencil. Take away the lens. Eliminate the rectangle using the utility knife. Take away the cutout rectangle in the shoe box half. Put the lens from the cutout rectangle. Tape the lens towards the shoe box with strips of duct tape.
6
Put the 1 / 2 of the shoe box facedown on the ground using the fresnel lens facing the wall. Fall into line the 2 shoe box halves to ensure that they're despite one another.
7
Turn the LED torch on. Switch off the area light. Move the shoe box half which has the fresnel lens toward another shoe box half to concentrate the look from the slide that's now being forecasted around the wall.
Tips & Alerts
The thin style of a fresnel lens causes it to be perfect for taking more oblique light compared to a bulky glass lens.
1
Take away the cover in the shoe box. Put the shoe box flat facedown on the work surface. Measure across the size of the shoe box having a tape-measure. Cut with the shoe box in the midway point having a utility knife.
2
Stand each 1 / 2 of the shoe box to ensure that the cut finish is facing lower. Put the reflector from the LED torch against the top among the shoe box halves. Draw a circle round the reflector around the shoe box having a pencil. Take away the LED torch. Eliminate the circle using the utility knife. Take away the cutout circle in the shoe box half.
3
Contain the slide to ensure that the dull side is facing you. Tape the slide towards the reflector from the LED torch with strips of duct tape. Put the reflector from the LED torch from the cutout circle. Tape the reflector towards the shoe box with strips of duct tape.
4
Put the 1 / 2 of the shoe box which has the LED torch facedown on the ground a feet from a wall using the LED torch facing you.
5
Put the fresnel lens against the top other shoe box halves. Draw a plan round the lens around the shoe box having a pencil. Take away the lens. Eliminate the rectangle using the utility knife. Take away the cutout rectangle in the shoe box half. Put the lens from the cutout rectangle. Tape the lens towards the shoe box with strips of duct tape.
6
Put the 1 / 2 of the shoe box facedown on the ground using the fresnel lens facing the wall. Fall into line the 2 shoe box halves to ensure that they're despite one another.|SMD 5050 RGB LED Bar 30LEDS
7
Turn the LED torch on. Switch off the area light. Move the shoe box half which has the fresnel lens toward another shoe box half to concentrate the look from the slide that's now being forecasted around the wall.
Tips & Alerts
The thin style of a fresnel lens causes it to be perfect for taking more oblique light compared to a bulky glass lens.A LED projector is much like any projector for the reason that it takes a lens to concentrate the look although, unlike those of an incandescent bulb, the LED source of light uses less energy and does not generate warmth. You may make your personal LED slide-like projector from the couple of supplies acquired from the hobby store or electronics store, coupled with an LED torch. A couple of supplies that many homes may have available is going to be needed too.
1
Take away the cover in the shoe box. Put the shoe box flat facedown on the work surface. Measure across the size of the shoe box having a tape-measure. Cut with the shoe box in the midway point having a utility knife.
2
Stand each 1 / 2 of the shoe box to ensure that the cut finish is facing lower. Put the reflector from the LED torch against the top among the shoe box halves. Draw a circle round the reflector around the shoe box having a pencil. Take away the LED torch. Eliminate the circle using the utility knife. Take away the cutout circle in the shoe box half.
3
Contain the slide to ensure that the dull side is facing you. Tape the slide towards the reflector from the LED torch with strips of duct tape. Put the reflector from the LED torch from the cutout circle. Tape the reflector towards the shoe box with strips of duct tape.
4
Put the 1 / 2 of the shoe box which has the LED torch facedown on the ground a feet from a wall using the LED torch facing you.|LED Strip Light
5
Put the fresnel lens against the top other shoe box halves. Draw a plan round the lens around the shoe box having a pencil. Take away the lens. Eliminate the rectangle using the utility knife. Take away the cutout rectangle in the shoe box half. Put the lens from the cutout rectangle. Tape the lens towards the shoe box with strips of duct tape.
6
Put the 1 / 2 of the shoe box facedown on the ground using the fresnel lens facing the wall. Fall into line the 2 shoe box halves to ensure that they're despite one another.
7
Turn the LED torch on. Switch off the area light. Move the shoe box half which has the fresnel lens toward another shoe box half to concentrate the look from the slide that's now being forecasted around the wall.
Tips & Alerts
The thin style of a fresnel lens causes it to be perfect for taking more oblique light compared to a bulky glass lens.
订阅：
博文 (Atom)