Building a Slide Film Lamp

Photography enthusiasts and enthusiasts who've boxes of 35mm slides that should be organized and scanned might find it helpful to produce a portable and affordable lamp to light up 35mm slides. You are able to develop a lamp using materials at home improvement and budget decorating stores. The sunshine box supplies a stable surface to keep 35mm slides and backlighting to see the pictures to help you have a digital photograph from the slide. You may also adapt this lamp design to satisfy needs beyond viewing 35mm slides, for example developing a lighted picture frame, tracing surface or small, lighted display.||MR16 LED SpotLight

        1

        Select a picture frame with wide sides (for example three or four inches throughout) to produce a table-like top within the lamp.

        2

        Turn the image frame over to ensure that the glass is facing lower and put on the flat working surface.

        3

        Take away the back plate from the picture frame store the picture in position.

        4

        Appraise the area a minimum of 1/2 inch in the picture opening (this ought to be slightly bigger compared to picture size). For instance, the measurement to have an 8-by-10 picture is 9-by-11.

        5

        Glue the glass towards the frame and hang it aside to dry and cure completely.

        For longer use, consider changing the glass within the picture frame having a obvious, thick plastic panel (cut towards the same size because the glass) and glue this sheet towards the inside edges from the frame.

        6

        Cut the wood towards the measured measures from Step Four. For instance, a measurement of 9-by-11 requires cutting two measures of 9 inches and 2 measures of 11 inches.

        7

        Drill single-inch hole on both sides of the lengthy period of wood, roughly 2 " in the finish, to support the energy cord for each one of the LED Bulb Lamp.

        8

        Assemble the 4 bits of wood to produce a wide open box.

        9

        Secure the corners and sides from the box using wood screws.

        10

        Fresh paint the inside walls from the box with two jackets of whitened fresh paint and permit to dry completely.

        11

        Install the compact, under-the-counter LED light fittings within each one of the shorter sides from the box. Make certain to center the sunshine fixture flat and up and down around the panel and orient the sunshine fixture to ensure that the energy cord is on a single side because the drilled holes.

        12

        Thread the energy cords with the drilled holes and plug right into a energy strip.

        13

        Put the picture frame face lower and put the sunshine box on the top from the frame. Trace a plan from the corners from the lamp on the rear of the image frame.

        14

        Take away the lamp and fix the corner brackets towards the picture frame to produce a help guide to contain the frame top in position.

        15

        Turn the frame over and put on the top from the lamp, ensuring the corner brackets work with the outdoors corners from the lamp.

        16

        Cut the translucent plastic glass to suit the image size (for instance, 8-by-10).

        17

        Take away the protective film around the plastic glass and put on the top from the glass surface.

        18

        Plug the energy cord from the energy strip into a power outlet and switch on the LED Panel Light.

        19

        Place 35mm slides on the top from the plastic glass to see the rear-lit images.

Tips & Alerts

    Have a variety of plastic glass of different translucency open to make use of the lamp for other reasons, for example tracing.

    If you are utilizing a longer frame (for example 11-by-13 or bigger), consider setting up compact LED strip lights around the lengthy side from the box.

    Make certain to set up the LED light fittings centered between your top and bottom to prevent getting too hot surfaces.

    To prevent cracking or breaking, don't apply pressure or weight towards the glass surface.

Steps to make an LED Blink to Music Having a Transistor

For any simple electronics project, making an LED blink to music having a transistor is all about as simple as they are available. If you have your soldering iron and solder, it's also an affordable project using the parts you'll need usually costing under $5 at any electronics parts supply store. After you have your parts, you may be finished in under an hour or so.||LED driver Module

        1

        Run electrical wire in the positive terminal from the 9-volt battery towards the positive leg on among the LEDs by hooking up an alligator clip towards the terminal and running the wire in the alligator clip towards the positive leg from the first LED.

        2

        Connect the LEDs in series by wiring the negative leg from the first LED towards the positive leg from the second LED, then your negative leg from the second LED towards the positive leg from the third LED.||LED Light Module


        3

        Wire the negative leg from the third LED towards the middle pin from the Tip31 transistor.

        4

        Wire the best pin from the from the Tip31 transistor towards the negative terminal from the battery while using alligator clip as pointed out in Step One.

        5

        Prepare the earphone cable by clipping the cord before it reaches the earphones. While using wire strippers, strip the rubber or plastic coating back about 1 " to reveal the 3 wires inside.

        6

        Connect the red-colored or whitened wire in the earphone cable 'either works' left pin from the from the Tip31 transistor. Then connect the floor wire right pin in which the link with battery can also be situated.||LED Panel Light


        7

        Solder all of your connections.

        8

        Plug the earphone wire right into a seem-producing source, switch on the background music and revel in.

Tips & Alerts

    Each LED requires 3 volts to operate. If you want to include more LEDs, you should also improve your energy size consequently.

    The quantity of electrical wire you'll need is dependent how far apart you need to space the LEDs.

    Change things up with various color LEDs.

How you can Wire a 12-Volt LED

LED lights are progressively popular for automotive, outside as well as household programs. You have to pay attention when wiring alternative containers for just about any LED lights. Unlike standard bulbs, LED lights are polarized. The "D" in LED means diode. A diode is definitely an electronic component made to pass electricity one way only. LEDs work on Electricity current which, unlike household AC current, keeps a continuing polarity on each lead.

        1

        Test out your energy source having a multi-meter. Set the number selector to Electricity 12V and put one probe on each energy source lead. Using the positive probe around the positive energy source lead, the meter's reading through is 12 . A reading through of 12- signifies the leads are corrected.

        2

        Identify the LED receptacle's positive terminal. This ought to be clearly marked having a " " or perhaps an "A." The "A" signifies anode.||LED Panel Light

        3

        Connect the positive add the energy source towards the positive terminal around the receptacle. Connect the negative result in the negative terminal.

Tips & Alerts

    LED bulbs created for household use have built-in energy plugs. These are made to screw into standard light electrical sockets without special wiring.||LED Flexible Strip

    In automotive, outside and marine programs, use containers created for LED lights. Affixing wiring straight to the devices with an LED may cause erratic performance and/or early failure.

How you can Use a Load Equalizer for LED Lights

If you have lately installed new LED (light giving off diode) turn signal lights inside your motorcycle, and they are flashing considerably faster than before, you will need to use a load equalizer to repair the problem. This really is because of the LED Down Light needing a smaller amount energy than stock incandescent lights. The burden deficit produced through the LEDs causes the turn signals to blink quicker. Load equalizers simulate a greater electrical load, making the turn signals blink in a more standard rate.
1
Turn the motorcycle off and take away the important thing. Locate the wiring harness that consists of the wires running for your front and back lights.
2
Stick to the wiring harness towards the plastic connector, usually situated underneath the chair from the motorcycle. Unplug the plastic connector.|10W LED Down Light
3
Plug a mans wiring harness plug in to the female plug around the load equalizer adapter, then plug the rest of the female finish in to the male side from the adapter. The burden equalizer adapter splits the turn signal and ground wires from the primary wiring harness and enables you to definitely connect the burden equalizer.
4
Plug the burden equalizer unit in to the load equalizer plug around the load equalizer adapter.|LED Panel Light
5
Switch on the motorcycle and try out the turn signals. A reduced rate of blinking than before signifies the load equalizer and adapter happen to be installed effectively. Otherwise, unplug and reunite the burden equalizer and adapter plugs.